jeep wrangler p0036

Cars related to phrase jeep wrangler p0036

jeep wrangler p0036 II TJ
jeep wrangler p0036 II TJ

Answers and questions: jeep wrangler p0036

JEEP WRANGLER II TJ TJ error code list

Maybe this should be a sticky....this is a list of all the codes that a TJ will throw at ya. You can get these codes by turning the key on and off 3-4 times within a 5 second time frame P-code suffixes (M) Check Engine Lamp (MIL) will illuminate during engine operation if this Diagnostic Trouble Code was recorded. (G) Generator Lamp Illuminated within 5 seconds. P0030 11 02 Sensor Heater Relay Malfunction

JEEP WRANGLER II TJ cannot remove 02 sensor. suggestions

ive been trying to remove my front 02 sensor for a bit of time now i gave it at least 3 or 4 different shots. ive tried all i can think of open ended wrench PB blaster 02 Sensor removal socket Vice Grips Adjustable pipe wrench. While engine was hot while cold heating with torch Nothing will take this damn thing off. Sadly im at the point where the fitting is almost rounded making it even more difficult Any other suggestions please thanks

P0135 is the exact one mine is throwing right now....unless you know the exact code with an O2 sensor you are taking shots in the dark. Here are the codes that deal with O2 sensors P0030 HO2S Heater Control Circuit Bank 1 Sensor 1 P0031 HO2S Heater Circuit Low Voltage Bank 1 Sensor 1 P0032 HO2S Heater Circuit High Voltage Bank 1 Sensor 1 p0036 Sensor heater relay problem p0036 HO2S Heater Control

JEEP WRANGLER Jeep Codes A long list

found these hope they help anyone here on the forum Back to Tech 1998 - Present jeep Error Codes Generic Scan Tool P-Code DRB Scan Tool Display Brief Description of DTC P0030 (M) 11 O2 Sensor Heater Relay Circuit Problem detected in oxygen sensor heater relay circuit. p0036 (M) 12 O2 Sensor Heater Relay Circuit Problem detected in oxygen sensor heater relay circuit. P0106 Barometric Pressure Out of

JEEP WRANGLER Throwing O2 sensor codes

The jeep is throwing codes for all 4 upstream O2 sensors P0031 P0051 P0136 P0157 I believe all of them are low voltage readings which indicates too much oxygen in the exhaust gases. Ive tried clearing them but they just come back. Anyone have any ideas how to fix this or what could be causing it. As an aside I drove the for a little while while the eng light was on (because of the above codes) and

Could that p0036 have benn a P0031 Is it possible you have a short Id look for a short to ground and check the fuses. From the FSM NOTE If P0031 and P0051 are set along with P0136 inspect the related fuse and repair as necessary.

Initially it was just those 3 and yes that was a typo on my part.....it should have been P0031 not p0036 I just checked the fuse and its blown. So now its a matter of tracking down the short. (nice call on your part) Any ideas of where to check I have no idea where the wiring is routed for these sensors.

Quote Originally Posted by jeepguy81 Initially it was just those 3 and yes that was a typo on my part.....it should have been P0031 not p0036 I just checked the fuse and its blown. So now its a matter of tracking down the short. (nice call on your part) Any ideas of where to check I have no idea where the wiring is routed for these sensors. Id start by tracing the wires from the sensors and go from there might be easy...

JEEP WRANGLER I YJ I got engine codes P 0456 and 0457

Hello all Check engine light came on today. I did the key trick and it displayed P0457 and then switched to 0456 after about a second. Dealer just put a new fuel pump in last week. Anyone know what these codes mean

GENERIC OBD II CODE DEFINITIONS P0010 A Camshaft Position Actuator Circuit (Bank 1) P0011 A Camshaft Position - Timing Over-Advanced or System Performance (Bank 1) P0012 A Camshaft Position - Timing Over-Retarded (Bank 1) P0013 B Camshaft Position - Actuator Circuit (Bank 1) P0014 B Camshaft Position - Timing Over-Advanced or System Performance (Bank 1) P0015 B Camshaft Position - Timing Over-Retarded

Ask an expert